For documentation on the current version, please check Knowledge Base.
Viewer Settings
This page documents the 3DM Viewer Settings.
Orbit 3DM Viewer > Sidebar > Settings icon
General
Viewer
Show Focus Position
The focus position is displayed in all view with a green cross.
Show Hover Position
The hover position is displayed in all views with a red cross.
Reference Ground height
Allows picking the ground height value by clicking in one of the 3D views.
The value is used for displaying 2D resources and is calculated as follows:
- On any image view: Z coordinate of the photo position viewpoint minus the height offset of the camera above ground, see Orbit run configuration.
- 3D point cloud view: Z coordinate of the 3D viewpoint downwards intersection with the point cloud. This technique will only be used if no image view has been opened.
Sidebar Position
Set the position of the Sidebar, the Viewer Menu is placed at the opposite side of the Viewer.
View Menu Position
Set the position of the view action menu to the center top, left top or left middle.
Search
Geocoding Service
Change the geocoding service used in the viewer.
- Available for everyone: Bing, Google
- Available for companies based in Belgium: Geopunt
Linear Reference Dataset
Select the linear reference dataset to be used for search and focus to a specific distance along the dataset.
Resources
Show Resource Type
Enable/disable the display of the resource type in the resource sidebar.
Set resource visibility by view
Display certain resources in one or more specific views. The buttons with the numbers or R (for reference view) are displayed in the Resources Sidebar under the name of each resource.
Reference View
Display Annotations
Enable the display of 3D annotations on the Reference View.
Display Image Resources
Enable the display of ortho image resources on the Reference View.
Display Pointcloud Resources
Enable the display of pointcloud resources on the Reference View.
Clip Pointcloud by Height of Active View
If pointcloud resources are displayed on the reference view, the pointclouds can be clipped by the height of the active view (indicated by the white highlighted frame)
Display Vector Resources
Enable the display of vector resources on the Reference View.
Allow multiple basemaps
Enable selecting multiple basemaps in the basemap selection menu.
Views
All Views
Display viewing direction label
Display the wind direction to which the views are aimed.
The label is displayed under the view action menu.
3D View
Display Base Map in 3D
Display the base map in the 3D view(s). The base map appears on the Reference Ground Height.
Drape Base Map on selected Terrain
Add 3D rendering to the base map. The z-values used for this are based on the chosen terrain model.
Stereo View Type
Choose from different stereo techniques to display the 3D View.
- Stereo Anaglyph
- Stereo Side-By-Side
- Stereo Side-By-Side (RHF)
- Stereo Side-By-Side (RVF)
- Stereo Top-Bottom
Lock Z Level
The Z level in the 3D views is fixed.
- Zoom, Pan = Pan in XY
- Pan in top 1/3 of view = Adjust Z level
- Rotate = Rotate around view coordinate
Image Views
Overlay Point Cloud on Image
Display the Point Cloud on the image in the view modes.
This can also be changed in the Resources Sidebar.
Display timestamp
Display the timestamp related to the opened in the view mode.
Display photo id
Display the photo id related to the opened image in the view mode.
Display resource name
Display the resource name related to the opened image in the view mode.
Get alternative images
Retrieve the list of alternative images when moving or adding a new image view.
Display photo positions at all times
Always display the photo positions in the image view. Not only when hovering over the position.
Overlay Image Annotations
Display the image annotations from the annotation xml files in the mapping resources.
Overlay Image Annotations
Display the image annotation tags from the annotation xml files in the mapping resources.
MM Planar and Spherical Image View
Maximum View Depth Annotations, Point Cloud and Vector Resources
Options to adjust the view depth visibility of the 3D annotations, point cloud and vector resources on the spherical and MM Planar image view (distance from the photo position).
Maximum Photo Search Distance
Set the maximum distance around the view coordinate to open a new image.
UAS Planar Image View
Maximum View Depth Annotations, Point Cloud and Vector Resources
Options to adjust the view depth visibility of the 3D annotations, point cloud and vector resources on the planar image view (distance from the photo position).
Maximum Photo Search Distance
Set the maximum distance around the view coordinate to open a new image.
Rotate Image to force north up
Option to choose if planar images should always face being rotated north up in the Planar View Mode.
Open automatically new best Image near edge of current image
When enabled, a new planar image will be opened in the Planar View Mode if the current image is dragged to the side. Drag to the left and a new planar image that is located on the right of the current image will be opened.
Measuring
General
Measure Technique
Choose the desired technique used for measurements.
Information about the measure techniques:
Display Coordinate Reference System
Allows selecting a CRS for displaying measurement results.
By default WGS84 will be used, additionally, point measurement results can be displayed in the CRS of any resource included in the publication or one that is specified in the set-up of the publication.
Hover
Hover Search Radius
The minimum and maximum value of the radius of the circle around the cursor in which point cloud points are searched to use for measurements.
Hover Gap Distance
The minimum distance between two points in order not to be considered part of the same cluster.
Min # Points
The minimum amount of detected points to form the hover
Show Hover
Show Used Points
Show Search Radius
Transparency
The transparency of the displayed measurements.
Results
Auto Save Measurements
Avoid the step to hit the save button by automatically saving measurements.
Display Units of Relative Measurements
Allows selecting meter, foot or yards as measuring unit.
Limit Decimals To
The number of decimals in the measurements.
Navigation
Gestures
Invert Zoom Direction
Reverse the direction of zooming when using the mouse wheel.
Default settings (switch icon is disabled): Push away to zoom out
Invert Tilt Direction
Reverse the direction of tilting. Default settings (switch icon is disabled): Push down for more nadir view
Mouse Left - Mouse Middle - Mouse Right
- Pan & Height
- Pan Only
- Rotate (Cursor Position)
- Rotate (View Center)
- Zoom
- Zoom (continuous)
Preset
Four configurations:
- Google
- OCP
- Orbit
- Iwtin
Synchronize
The Synchronize Settings enable the auto-update the position and orientation of one View based on the changing position and orientation of another View. The auto-updated View(s) will try to copy the position, orientation, and/or focus coordinate of the View it is synchronizing with.
Synchronize Views
Auto-update the other Individual Views based on an Individual View.
Synchronize Views From Reference
Auto-update all Individual Views based on the Reference View.
Synchronize Reference From Views
Auto-update Reference View based on an Individual View.
Floors
Enable Floor Filter
If the floor level is defined in the Resource Specs, the Floors functionality allows switching between different floors.
Resource Group by
Parent, Children: Resources will be grouped using the Floor settings of the Resource Group = Parent, or the single resources inside the group = children.
Timeline
Enable Time Filter
If a Start and Stop date is defined in the Resource Specs, the Timeline functionality allows to show the added resources grouped on a Timeline.
Set by
View - Workspace: A Timeline will be shown on each View, or one for the full workspace.
Group by
Day, Week, Month, Year: Resources will be grouped on the Timeline per Day, Week, Month or Year.
Resource Group by
Parent, Children: Resources will be grouped using the Date settings of the Resource Group = Parent, or the single resources inside the group = children.
View Action Menu
Enable/disable the available view action menus, only available when editing the workspace.
Move View
View Metadata
Image Play-Through
Option to make the play-through option visible in the View Mode Menu. The view mode will jump from one image to the next one automatically when the play-through is started.
Brightness
Photo Navigation by Sequence
Add the Sequence arrows to the View Mode Menu. Navigate through the planar or spherical images via the arrows or hitting the up and down arrow in the active view.
Photo Navigation by Relevance
Rotate in Photo Group
Rotate Oblique
Maximize
Download
Add the action to download images or pointcloud to the view action menu. Available when the download setting is enabled in the publication setup.
Focus
Add the action to focus all views on the current viewpoint. This is a one-time action.