Step 4: Photo Settings

This step is intended to be able to apply changes to parameters of individual photos.

e.g. sometimes the images are scanned in the opposite way than the flight direction was, not fitting into the camera definition.
In that case you want to turn the images according to their scan direction.

e.g. change the camera for all photos or for a selection of them.

e.g. you want to enter the width and height for the images expressed in pixels.

Press the 'Edit Settings…' button to get the next dialog:

At the left hand side you find the list of available photos in the project.

1. If you select one photo you will see the parameters for that photo on the right side.
2. Change one or more parameters.
3. Press the 'Modify Photo Properties' button to apply the changes.
   
   
   
   The changes are immediatly applied and active in the project.
   When you e.g. change the Kappa value, this will immediately be seen on the OrbitGIS overview or in an opened stereo viewer looking at a model where this image is part of.

1. Select one photo
2. Pressing the shift button while selecting a second photo will add the complete list of photos between the first and second photo to the selection.
3. Pressing the control button while selecting another photo will add this individual photo to the selection.
4. Once you made a selection of photos you will notice that all the values became insensitive.
5. Select now the parameters you want to change by pressing the square boxes before the parameter values
6. Update the values.
7. Press the 'Modify Photo Properties' button to apply the changes.
   
   

1. Make a selection of the photos you wish to take out of the project.
2. Press the 'Remove Photo' button.

1. Select a photo that has parameters close to the new photo you want to add.
2. Change the Name of this photo.
3. Change some other intended parameters.
4. Press the 'Add Photo' button to add this new photo to the project.
5. Here is an example of the dialog after adding a new photo:
   
   
   
   
   Don't forget to select the new photo and still correct the parameters using the button 'Modify Photo Properties' if you haven't done so before the 'Add Photo' button was pressed.
   When all changes are applied press the 'close' button to return to the wizard.
   
   

1. Name: the name of the photo must be exactly the same name of the image filename without the extension.
2. Select a camera: select a camera from the available lost in the drop down combobox.
3. Scan direction: it is possible that the image is rotated during the scanning phase against the normal situation displayed on the calibration document.
   Select the appropriate rotation angle to get the image back into a normal situation.
   To help you to make a fast and correct decision, use the 'Analyze orientation' button:
   • Analyze orientation:
     1. you can only press this button if you have selected at least two photos for which
        1. the images are available,
           
        2. and the kappa is oriënted in the main flight direction.
           
     2. Please select 2 images that are part of the main flight direction, e.g.:
        
        
        
        The image files have to be available because they will be viewed.
        
     3. Pressing the 'Analyze orientation' button will show the next 'Scan Direction Preview' dialog:
        
        .
        We can accept this setting (0 degrees) if the images would be used in this actual oriented situation
        (there is overlap between the images as they are shown).
        
     4. Pressing the option '180 degrees' gives the next situation:
        
        
        
     5. It is possible that in function of the provided imagery, we have only a good overlap between the images when selecting a scan direction different from 0.
        
     6. Press the 'Close' button to stop the preview.
        
     7. To change the 'Scan direction' for several photos at once (e.g. a strip), you must:
        1. Determine the correct “Scan Direction” for the requested photo's as explained above.
        2. Select the to be treated photo's.
        3. Select the 'Scan Direction' checkbox in front of the 'Analyze orientation' button.
        4. Select the 'Scan Direction' rotation angle (0, 90, 180 or 270 degrees).
        5. Press the 'Modify Photo Properties' button to make the change effective for all the selected photos.
           
4. Centrum X: the projection center's X coordinate.
5. Centrum Y: the projection center's Y coordinate.
6. Centrum Z: the projection center's Z coordinate.
7. Kappa: the kappa rotation angle expressed in radians.
   For vertical photogrammetry, Kappa is the rotation around the vertical axis.
8. Phi: the phi rotation angle expressed in radians.
   For vertical photogrammetry, Phi is the rotation around the axis defined by the wings of the airplane.
9. Omega: the omega rotation angle expressed in radians.
   For vertical photogrammetry, Omega is the rotation around the axis defined by flight direction of the airplane.
10. Width in image pixels: the width of the original digital image in number of pixels.
    This value is only necessary when using digital images without real fiducial marks.
11. heigth in image pixels: the height of the original digital image innumber of pixels.
    This value is only necessary when using digital images without real fiducial marks.
12. Number of tiepoints: the actual number of observations made in this photo used as tiepoint.

1. Go to the next wizard step by pressing the button on the wizard dialog.